|
|
|||||||||||||||||
| PSU Specification : | X2022APFC STP1650M CX20霧黑銀粉烤漆 | Model : | STP-1650M | Test Stage | |||||||||||||
| Vendor : | Soly-tech | EVT | DVT | PVT | |||||||||||||
| P/N : | STP-1650M | Sample Rev. : | A00 | Test Date : | 2023/4/18 | Test Fixture: | |||||||||||
| Tested By: | lizhehui | Checked By: | liangyunjing | PSU S/N: | |||||||||||||
| Item | Test Item | Results | Remark | Comment | Design Margin | SCOPE SETTING | 備註 | ||||||||||
| B.W(MHZ) | Acq | Couple | |||||||||||||||
| 1 | Visual Inspection | PASS | Visual Inspection | N.A | N.A | NA | NA | NA | |||||||||
| 2.1 | AC Input Requirement | Input Current RMS | PASS | Input RMS Current | 3.1.1 | N.A | 20 | HI-RES | NA | ||||||||
| 2.2 | Brown out/Brown out Recovery | PASS | Brown out | 3.1.4 | Bi=85Vac. Bo=65Vac | 20 | HI-RES | NA | |||||||||
| 3.0 | Input Over Current Protection | PASS | Input Over Current Protection | 3.1.1 | 95% | 20 | HI-RES | NA | |||||||||
| 4.0 | Inrush Current | PASS | Inrush Current | 3.1.5 | 95% | 20 | HI-RES | NA | |||||||||
| 5.0 | Efficiency | PASS | Efficiency | 3.1.6 / 3.2.4 | 1% Eff to 20%; 0.5% Eff to 50% and 100% | NA | NA | NA | |||||||||
| 7.0 | Stabdby Efficiency | PASS | Standby Eff, | 3.2.4 | <0.5W | NA | NA | NA | |||||||||
| 8.0 | Auto Restart | PASS | Auto Restart | 3.1.9 | N.A | 20 | HI-RES | DC | |||||||||
| 10.0 | Harmonic | PASS | Harmonic | 3.13 | N.A | NA | NA | NA | |||||||||
| 11.0 | Slow Line Transients (Surge) | PASS | Vin Surge | 3.1.8 | N.A | 20 | HI-RES | DC | |||||||||
| 12.0 | AC Dropout | PASS | AC Dropout | 3.1.7 | N.A | 20 | HI-RES | DC | |||||||||
| 13.0 | DC Voltage Regulation / DC Output Current | PASS | Regulation | 3.2.1/ 5.7 | +/- 5% for all output rails, beside -12V | NA | NA | NA | |||||||||
| 14.0 | No Load | PASS | No Load | 5.7 | N.A | 20 | HI-RES | DC | |||||||||
| 15.0 | Output Ripple and Noise | PASS | Ripple and Noise | 3.2.3 | 120mV for 12V and -12V rail; 50 mV for other rails | 20 | Envelope*10 | AC | |||||||||
| 16.0 | Output Transient Response(Dynamic Loading) | PASS | Dynamic | 3.2.5 | +/- 5% for all output rails, beside -12V | 20 | HI-RES | DC | |||||||||
| 17.0 | Close-Loop Stability | #REF! | Close-Loop Stability | 3.2.7 | N.A | NA | NA | NA | |||||||||
| +5VDC / +3.3VDC Power / Sequencing | PASS | Tracking | 3.2.8 | 5V>3.3V at least 0.5V | 20 | HI-RES | DC | ||||||||||
| 18.0 | Capacitive Loading | PASS | Capacitive Loading | 3.2.6 | N.A | 20 | HI-RES | DC | |||||||||
| 19.0 | Overshoot at Turn On/Off | PASS | Overshoot | 4.7 | <10% of regulation | 20 | HI-RES | DC | |||||||||
| 20.0 | Protection | Over Current Protection | PASS | OCP | 5.4 | N.A | 20 | HI-RES | DC | ||||||||
| 21.0 | Short Circuit Protection | PASS | SCP | 5.1 | N.A | 20 | HI-RES | DC | |||||||||
| 22.0 | Over Voltage Protection | PASS | OVP | 5.2 | N.A | 20 | HI-RES | DC | |||||||||
| 41.0 | Over Power Protection | PASS | OPP | 5.3 | N.A | 20 | HI-RES | DC | |||||||||
| 23.0 | Reset After Shutdown | PASS | Reset After Shutdown | 5.6 | N.A | 20 | HI-RES | DC | |||||||||
| 26.0 | Control and Logic Signals Ripple and Noise | PASS | POK@PS_ON RP | 4.1 /4.2 | N.A | 20 | HI-RES | AC | |||||||||
| 27.0 | Remote ON/OFF control | PASS | Remote ON@OFF control | 4.2 | N.A | 20 | HI-RES | NA | |||||||||
| 28.0 | Current Validation PS_ON | PASS | PS_ON Signal | 4.2 | N.A | 20 | HI-RES | DC | |||||||||
| 29.0 | POWER GOOD SIGNAL (POK, or P_GOOD) | PASS | Power Good Signal | 4.1 | N.A | NA | NA | NA | |||||||||
| 30.0 | Glitches | PASS | AC-On & AC-Off | 4.5 | N.A | 20 | HI-RES | DC | |||||||||
| 31.0 | Logic Timings(Glitches) | Power-on time ( T1 ) | PASS | T1 | 4.4 | <500msec | 20 | HI-RES | DC | ||||||||
| 32.0 | Rise Time ( T2 ) | PASS | T2 | 4.5 / 4.7 | >0.1msec ; < 20 msec | 20 | HI-RES | DC | |||||||||
| 33.0 | PWR_OK Delay ( T3 ) | PASS | T3 | 4.0 | >100mse ; < 500 msec | 20 | HI-RES | DC | |||||||||
| 34.0 | PG Rise Time ( T4 ) | PASS | T4 | 4.0 | <10 msec | 20 | HI-RES | DC | |||||||||
| 35.0 | AC loss to PWR-OK hold-up Time ( T5) | PASS | T5 | 4.6 | >16 msec | 20 | HI-RES | DC | |||||||||
| 36.0 | PWR_OK inactive to DC Loss Delay (T6) | PASS | T6 | 4.0 | > 1 msec | 20 | HI-RES | DC | |||||||||
| 40.0 | Standby Turn-Off | PASS | Standby Turn-Off | 4.8 | N.A | 20 | HI-RES | DC | |||||||||
| 42.0 | UPS | #REF! | UPS | Internal | 20 | HI-RES | DC | ||||||||||
| 6.0 | Blue Angel / Energy Star 4.0 Requirement | 4.5W-2.5W | 20 | HI-RES | DC | ||||||||||||
| 37.0 | AC-ON to Outputs Turn-on Delay Time ( T7 ) | T7 | 20 | HI-RES | DC | ||||||||||||
| 38.0 | PS-OFF to Outputs Turn-off Delay Time ( T8 ) | T8 | 20 | HI-RES | DC | ||||||||||||
| 39.0 | PS-ON to Outputs Turn-on Delay Time ( T9 ) | T9 | 20 | HI-RES | DC | ||||||||||||
| 24.0 | Common Mode Noise | Common Mode Noise | 20 | HI-RES | DC | ||||||||||||
| 9.0 | Active PFC (Power Factor Correction) | PF | 3.1.6 | 20 | HI-RES | DC | |||||||||||
| Attention: | |||||||||||||||||
| 1. Use CC Mode For Overall Test Item | |||||||||||||||||
| 2. Before Timing Test Need Warm Up 30 Minutes | |||||||||||||||||
| 3. Ripple Noise Scope Acq. Set Envelope*10 Mode | |||||||||||||||||
| 4. PG/Ps-on/Common Current Acq. Set Sample Mode | |||||||||||||||||
| 5. Other Test Item Acq. Set Hi-Resolution Mode | |||||||||||||||||
| 6. Ripple & noise use scpoe probe , Coupling AC | |||||||||||||||||